Author Topic: Access Violation-Make Network (Read 7335 times)

hardwire · « **on:** April 25, 2005, 06:05:12 PM »

I know I have done this fine on previous versions. But.... I have made 3 tracks in an area and wanted to use the MAKE A NETWORK option. It runs then errors about halfway with the following error...

I have tried using each of them individually but it get the same error??
LOG:
TopoFusion 2.50 Log Begin
Windows Major Version: 5
Windows Minor Version: 1
Windows Build Number : 2600
Windows Platform ID Â : 2
<snip>
recreateVideoMemoryPool: Finishing up

Caught Exception:
Function: ManagerThread (Network)
Exception: Access Violation

alizhan · « **Reply #1 on:** April 26, 2005, 06:21:42 PM »

Yeah, I've had this problem off and on as long as I remember. Same spartan log message as you get. I find that restarting Windows (not just TF, the whole computer) sometimes helps, but not always. Some tracks just won't convert. I'll send one in.

hardwire · « **Reply #2 on:** April 26, 2005, 06:58:39 PM »

This evening I went back to my old tracks to make sure I was not dreaming and all of them work fine ...

'> So it sounds like it is not the version....

'>

hardwire · « **Reply #3 on:** May 01, 2005, 10:37:13 AM »

Hmmm I may have discovered a repeatably problem... Â

'> Looks like it is related to the first few track points.... This first picture gets the error...

and when I move the first point down so it does Â not cross the trail like this...

It makes a network just fine without a problem....
It seems to be related to just the beginning of the trail.... Because, and don't laugh Â ':p'

Â SInce I was having problems locating this cache, I went in circles a few times ... this one one makes a network just fine...

tdcarter · « **Reply #4 on:** May 02, 2005, 08:41:36 AM »

I also got the violation... but I didn't restart winders, just TF.

Ran the same network trails again, and also got it.

I tried moving the top listed track down the list (remove & re-add), it was actually right in the middle of the network, and re-ran and it worked.

I looked at the TF log, and it shows a DirectX error right after catching the violation.. speciafically:

DirectX Error [2405]: Access to this surface is being refused because the surface is already locked by another thread.

I saved the log if anyone wants it?

TC

Alan · « **Reply #5 on:** May 02, 2005, 04:53:59 PM »

Scott will have to take a look at this, he wrote all the network code. He's out riding the Arizona trail currently. He should be back in a couple weeks.

hardwire · « **Reply #6 on:** May 02, 2005, 05:10:23 PM »

Gosh, no problem....

'> I wish I was out there! Wonderful tool!

Jimt · « **Reply #7 on:** May 03, 2005, 10:23:45 PM »

I read this post today, as I was having exactly the same issues. I was reassembling a single loop from a series of walks that covered much of the same ground. So I had to cut out lots of duplicate tracks resulting in occaisional breaks in the original loop. Before using the "make network" to stitch these segements into one continuous loop, I went back to make sure that no lines intersected. All the segments were touching, and there were not cross-over points. But still "make network" barfed, as described in the previous posts. Something is too unstable in this function...

tdcarter · « **Reply #8 on:** May 07, 2005, 05:21:09 PM »

Try changing the order of them (segments) in the list.

Worked for me.... least, this time.